Reelcraft D84050OMP | 1 in. x 50 ft. Premium Duty Hose Reel
Reelcraft D84050OMP | 1 in. x 50 ft. Premium Duty Hose Reel
Accept Credit Cards
Official PayPal Seal

Reelcraft D84050OMP | 1 in. x 50 ft. Premium Duty Hose Reel Industries Inc_150px.jpg
Availability: In Stock
Part Number: RLCD84050OMP
0 Review(s)
Write a Review
Retail Price:$1,401.96
Your Savings:$127.45(9%)
  • Low prices.

    Price match guarantee

  • In-House Experts.

    We know our products

  • Easy Returns.

    Quick & Hassle Free

  • Superior Selection.

    Extensive product catalog

Reelcraft's Series 80000 spring retractable hose reels incorporate the most current design and manufacturing techniques to guarantee long life and trouble-free performance. The reels all-steel construction and baked-on powder coat finish combine to produce a rugged, corrosion-resistant product suitable for a wide variety of applications. Series D80000 hose reels are also supplied with Reelcraft's ball-bearing style swivel.

Key Features - Reelcraft D84050OMP

  • Reinforced steel – The steel guide arm and dual pedestal base are stamped with ribs and gussets and robotically welded to ensure maximum strength and lightest possible weight. The unitized cast fluid path and ratchet reduce wearable parts and ease of assembly.
  • Full flow stress free swivel design – The full flow swivel combines the highest grade seal design and materials with bearing areas to ensure maximum service life.
  • Quality finish and corrosion resistant – Individually powder coated components offer the maximum protection from premature corrosion.
  • Made in USA

Dimension Drawing - Reelcraft D84050OMP

Click image to enlarge.Click image to enlarge.

Specifications - Reelcraft D84050OMP

Weight122 lbs
Hose I.D.1"
Hose O.D.1.400"
Hose Length50'
Pressure1275 psi
Hose End1" NPT(M)
Inlet1" NPT(F)
Reel Outlet1" NPT(F)
Hose IncludedYes
Max Temperature210 °F

Fluid Path Materials - Reelcraft D84050OMP

Shaft MaterialAluminum

FAQs - Reelcraft D84050OMP

How do I increase or reduce spring tension?To increase spring tension:

Adding wraps of hose will increase spring tension. This can be accomplished by pulling out approximately 10 feet of hose, hand feed hose back up through roller bracket assembly until loop is large enough to slip over sheave. Add two or three wraps until desired tension is achieved. Do not exceed spring capacity.’

To reduce spring tension:

This can be accomplished by removing wraps of hose from the reel sheave. Remove wraps of hose from the sheave, one wrap at a time, until desired tension is obtained.

For Series D9000 reels, you will have to remove the bumper and control handle then feed the end of the hose through the roller bracket assembly to add or remove wraps of hose from the reel drum.

Can my spring driven reel be made "constant tension"?

While most Reelcraft spring retractable reels can be made “constant tension” at the factory or by simply removing the latching system there are some models that may not have this capability.

Please contact Reelcraft Customer Service to assure that the specific reel you have or require is capable of or available as a “constant tension” model.

How do I install a new drive spring and set pre-turns?We have several different types of spring driven reels. Each require a slightly different set of instructions. For “How-To” instructions on replacing a drive spring please have your reel model or drive spring number available and consult customer service for instructions.
How many GPM's will I get from my hose?GPM = gallons per minute is a function of hose diameter, hose length, supply pressure and fluid going through the hose / reel. The most common fluids, air and water, can be seen in charted data. For hydraulic oils it is necessary to know the operating temperature, pressure and fluid viscosity.
What to do if there is restricted air pressure or fluid flow?U-bolts tightened down too tight on hose restricting product flow. Loosen U-bolts to be snug on outside diameter of hose but not too much that it crimps off product flow.
What if the hose or cord does not retract?Insufficient spring tension

Adjust spring tension by adding wraps of hose. Pull out approximately 10 feet of hose. Hand feed hose back up through roller bracket assembly until loop is large enough to slip over sheave. Add two or three wraps until desired tension is achieved. Do not exceed spring capacity.

Hose / cord reel mounted on ceiling above 16 feet

Must special order heavier gauge spring steel for drive spring to overcome weight of hose / cord extending from reel. Control handle weight must also be considered. Contact Reelcraft for further information.

Latch mechanism engaged with drive spring coiled to solid height

U-bolt hose clamps on sheave assembly not positioned correctly.

Hose / cord fully extended will not retract

Latch mechanism engaged with drive spring is coiled to solid height. U-bolt hose clamps on sheave assembly are not positioned correctly.

Product supply to reel, rigid, plumbed in

If flexible connecting hose is not used between hose reel inlet and hard plumbing, you stand the chance of causing excessive bind to main shaft and hub bearings causing reel not to retract. This also voids warranty.

Reel mounted on uneven surface

Bolting the reel down to an uneven surface will distort side frame causing a bind on main support shafts restricting smooth retraction of hose.

Wrong guide arm position

If guide arm is in side wind position for ceiling mounted reels, hose / cord is bending at a 90° angle over roller bracket assembly causing excessive loss of spring tension. Adjust guide arm to coincide with how hose / cord reel is actually mounted. U-bolt clamps may need to be adjusted accordingly.

Broken main spring, broken spring arbor, corrosion on shaft and hub

Replace broken part with new. For corrosion: disassemble reel and remove corrosion, lubricate and reassemble.

material is leaking from the swivel. What do i do?O-ring worn out or wrong O-ring for material being handled

Replace O-rings with O-ring kit or replace with correct rings for material being handled.

Swivel maybe loose or not enough pipe thread sealant on shaft threads

Replace O-rings with O-ring kit or replace with correct rings for material being handled.

What to do if the reel does not latch?This could mean it has a broken latch spring, bent latch pawl or latch plate. The broken part(s) will need to be replaced.

Videos - Reelcraft D84050OMP

Series 80000 hose reelsClick to View
How to install a spring driven reelClick to View
How to replace the latch springClick to View
How to change a guide armClick to View
How to adjust spring tensionClick to View
How to position the guide armClick to View
What to do if the reel does not latch?Click to View

CAD Drawings - Reelcraft D84050OMP

CAD PDF 2D DrawingClick to View
CAD IGS 3D DrawingClick to View
CAD STP 3D DrawingClick to View

Documents and Downloads - Reelcraft D84050OMP

Catalog PageClick to View
Service ManualClick to View
New latch mounting bracket assemblyClick to View
Convert reel to constant tensionClick to View
Hose replacement and required wrapsClick to View
Pressure drop / flow rate charts and graphsClick to View
Material compatibility tablesClick to View

Parts/Accessories - Reelcraft D84050OMP

4HR1005 - Adjustable Bumper StopClick to View
600801 - 340° Pivot BaseClick to View
600980 - Wall Mounted Universal Swing BracketClick to View

Recently Viewed Items