Kent Moore Tools EN-49960 | EN-49960 Injector Nozzle Sleeve Puller (EN49960)

Nozzle Puller

Type Nozzle Puller

The current service procedure to replace the injector nozzle sleeve involves removing the cylinder head. EN-49960 allows injector nozzle sleeve replacement with the head installed on the engine. EN-49960-3 Remover is seated into the nozzle sleeve, and turned counter-clockwise with a wrench to unscrew it from the cylinder head. If a sleeve spins without removal, a slide hammer with 1/2"-13 thread (such as J-23907-1) is installed into EN-49960-3, and used to remove the nozzle sleeve. Once the new sleeve is ready for installation, it is placed onto EN-49960-1 Installer Guide, and seated lightly into the head with a hammer against EN-49960-1. The Injector clamp is used to hold EN-49960-1 and the sleeve in place. EN-49960-3 Swager is guided through EN-49960-1, and seated with a hammer. The included hardware is then threaded onto to EN-49960-3 remove it from EN-49960-1;"The current service procedure to replace the injector nozzle sleeve involves removing the cylinder head. EN-49960 allows injector nozzle sleeve replacement with the head installed on the engine. EN-49960-3 Remover is seated into the nozzle sleeve, and turned counter-clockwise with a wrench to unscrew it from the cylinder head. If a sleeve spins without removal, a slide hammer with 1/2""-13 thread (such as J-23907-1) is installed into EN-49960-3, and used to remove the nozzle sleeve. Once the new sleeve is ready for installation, it is placed onto EN-49960-1 Installer Guide, and seated lightly into the head with a hammer against EN-49960-1. The Injector clamp is used to hold EN-49960-1 and the sleeve in place. EN-49960-3 Swager is guided through EN-49960-1, and seated with a hammer. The included hardware is then threaded onto to EN-49960-3 remove it from EN-49960-1"

Kent Moore Tools - EN-49960 - Product Categories

• Hand Tools
• Pullers
• Pullers and Pushers

Kent Moore Tools - EN-49960 - Features

• Allows injector nozzle sleeve replacement with the head installed on the engine
• Remover is seated into the nozzle sleeve, and turned counter-clockwise with a wrench to unscrew it from the cylinder head
• If a sleeve spins without removal, a slide hammer with 1/2"-13 thread (such as J-23907-1) is installed into EN-49960-3, and used to remove the nozzle sleeve
• Once the new sleeve is ready for installation, it is placed onto EN-49960-1 Installer Guide, and seated lightly into the head with a hammer against EN-49960-1
• The Injector clamp is used to hold EN-49960-1 and the sleeve in place
• EN-49960-3 Swager is guided through EN-49960-1, and seated with a hammer
• The included hardware is then threaded onto to EN-49960-3 remove it from EN-49960-1
• Applications
• :
• Diesel Engines
• Benefits
• :
• Saves time and money by allowing injector nozzle sleeve replacement with the head installed on the engine
• Easy to use
• Reliable
• The current service procedure to replace the injector nozzle sleeve involves removing the cylinder head
• EN-49960 allows injector nozzle sleeve replacement with the head installed on the engine
• If working on 2011 or newer 4HK1 you will need the EN-50547.
• Isuzu FSR 2001 and 2002 Diesel 6HK1 7.8L 7800 Duramax Diesel.
• Isuzu FTR 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 and 2011 6HK1 7.8L 7800 Duramax Diesel.
• Isuzu FVR 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 and 2011 6HK1 7.8L 7800 Duramax Diesel.
• Isuzu FXR 2004, 2005, 2006, 2007, 2008, 2009, 2010 and 2011 6HK1 7.8L 7800 Duramax Diesel.
• Isuzu NPR 2005, 2006, 2007, 2008 and 2009 4HK1 5.2L Diesel.
• Isuzu NPR-HD 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012 and 2013 4HK1 5.2L Diesel.
• Isuzu NQR 2005, 2006, 2007, 2008, 2009 and 2010 4HK1 5.2L Diesel.
• Isuzu NRR 2005, 2006, 2007, 2008, 2009 and 2010 4HK1 5.2L Diesel.
• EN-49960 allows injector nozzle sleeve replacement with the head installed on the engine. EN-49960-3 Remover is seated into the nozzle sleeve, and turned counter-clockwise with a wrench to unscrew it from the cylinder head. If a sleeve spins without removal, a slide hammer with 1/2"-13 thread (such as J-23907-1) is installed into EN-49960-3, and used to remove the nozzle sleeve.
• Once the new sleeve is ready for installation, it is placed onto EN-49960-1 Installer Guide, and seated lightly into the head with a hammer against EN-49960-1. The Injector clamp is used to hold EN-49960-1 and the sleeve in place. EN-49960-3 Swager is guided through EN-49960-1, and seated with a hammer. The included hardware is then threaded onto to EN-49960-3 remove it from EN-49960-1.
• Manufacturer: SPX/Bosch (OTC Rotunda Kent-Moore Miller)

Kent Moore Tools - EN-49960 - Overview

• Kent-Moore Tools
• Kent-Moore EN-49960 Injector Nozzle Sleeve Puller
• The current service procedure to replace the injector nozzle sleeve involves removing the cylinder head. EN-49960 allows injector nozzle sleeve replacement with the head installed on the engine. EN-49960-3 Remover is seated into the nozzle sleeve, and turned counter-clockwise with a wrench to unscrew it from the cylinder head. If a sleeve spins without removal, a slide hammer with 1/2"-13 thread (such as J-23907-1) is installed into EN-49960-3, and used to remove the nozzle sleeve. Once the new sleeve is ready for installation, it is placed onto EN-49960-1 Installer Guide, and seated lightly into the head with a hammer against EN-49960-1. The Injector clamp is used to hold EN-49960-1 and the sleeve in place. EN-49960-3 Swager is guided through EN-49960-1, and seated with a hammer. The included hardware is then threaded onto to EN-49960-3 remove it from EN-49960-1

Kent-Moore Tools - EN-49960 - Specifications

Brand Name	Kent-Moore Tools
Manufacturer Part Number	EN-49960
Item Description	Kent-Moore EN-49960 Injector Nozzle Sleeve Puller (EN49960)
UNSPSC	27111712
Product Group Id	KM00
MS Bin Code	EP042
Shipping Weight	6lbs