Reelcraft SWHD76050OLPT | 3/8 in. x 50 ft. Single Line Welding Hose Reel T-Grade
Reelcraft SWHD76050OLPT | 3/8 in. x 50 ft. Single Line Welding Hose Reel T-Grade
Accept Credit Cards
Official PayPal Seal

Reelcraft SWHD76050OLPT | 3/8 in. x 50 ft. Single Line Welding Hose Reel T-Grade

assets/images/Reelcraft Industries Inc_150px.jpg
Availability: In Stock
Part Number: RLCSWHD76050OLPT
0 Review(s)
Write a Review
$580.52
Retail Price:$595.61
Your Savings:$15.09(3%)
product-shipping
  • Low prices.

    Price match guarantee

  • In-House Experts.

    We know our products

  • Easy Returns.

    Quick & Hassle Free

  • Superior Selection.

    Extensive product catalog

The new Reelcraft Series SW single line hose reel expands the industry-leading welding series and is specifically designed to improve work area safety and increase efficiency and productivity when transferring fuel gases.

Reel is shipped in the top wind position. The reel image is shown in the side wind position.




https://www.autotoolworld.com/assets/icons/features.jpg

Key Features

  • Reel
  • Hard coated wear-resistant aluminum double-sealed full flow swivel
  • Corrosion-resistant baked-on powder coat
  • Hose
  • Ideal for welding service – meets ARPM IP-7 and CGA E-1 standards for T-grade
  • Non-conductive
  • Tube: Synthetic rubber compound compatible with all common welding fuel gases
  • Reinforcement: Spiral synthetic yarn
  • Cover: Red synthetic rubber with ribbed surface



https://www.autotoolworld.com/assets/icons/specs.jpg

Specifications

Weight45 lbs
SeriesSW
Hose I.D.3/8"
Hose O.D.0.53"
Hose Length50'
Pressure200 psi
Hose End9/16 – 18 LH(F)
Inlet1/2" NPT(F)
Reel Outlet9/16-18(M)
Hose IncludedYes
Max Temperature150 °F
UPC699567027249



https://www.autotoolworld.com/assets/icons/specs.jpg

Fluid Path Materials

Shaft MaterialSteel



https://www.autotoolworld.com/assets/icons/faq.jpg

FAQs

How do I increase or reduce spring tension?To increase spring tension:

Adding wraps of hose will increase spring tension. This can be accomplished by pulling out approximately 10 feet of hose, hand feed hose back up through roller bracket assembly until loop is large enough to slip over sheave. Add two or three wraps until desired tension is achieved. Do not exceed spring capacity.’

To reduce spring tension:

This can be accomplished by removing wraps of hose from the reel sheave. Remove wraps of hose from the sheave, one wrap at a time, until desired tension is obtained.

For Series D9000 reels, you will have to remove the bumper and control handle then feed the end of the hose through the roller bracket assembly to add or remove wraps of hose from the reel drum.

Can my spring driven reel be made "constant tension"?

While most Reelcraft spring retractable reels can be made “constant tension” at the factory or by simply removing the latching system there are some models that may not have this capability.

Please contact Reelcraft Customer Service to assure that the specific reel you have or require is capable of or available as a “constant tension” model.

How do I install a new drive spring and set pre-turns?We have several different types of spring driven reels. Each require a slightly different set of instructions. For “How-To” instructions on replacing a drive spring please have your reel model or drive spring number available and consult customer service for instructions.
What to do if there is restricted air pressure or fluid flow?U-bolts tightened down too tight on hose restricting product flow. Loosen U-bolts to be snug on outside diameter of hose but not too much that it crimps off product flow.
What if the hose or cord does not retract?Insufficient spring tension

Adjust spring tension by adding wraps of hose. Pull out approximately 10 feet of hose. Hand feed hose back up through roller bracket assembly until loop is large enough to slip over sheave. Add two or three wraps until desired tension is achieved. Do not exceed spring capacity.

Hose / cord reel mounted on ceiling above 16 feet

Must special order heavier gauge spring steel for drive spring to overcome weight of hose / cord extending from reel. Control handle weight must also be considered. Contact Reelcraft for further information.

Latch mechanism engaged with drive spring coiled to solid height

U-bolt hose clamps on sheave assembly not positioned correctly.

Hose / cord fully extended will not retract

Latch mechanism engaged with drive spring is coiled to solid height. U-bolt hose clamps on sheave assembly are not positioned correctly.

Product supply to reel, rigid, plumbed in

If flexible connecting hose is not used between hose reel inlet and hard plumbing, you stand the chance of causing excessive bind to main shaft and hub bearings causing reel not to retract. This also voids warranty.

Reel mounted on uneven surface

Bolting the reel down to an uneven surface will distort side frame causing a bind on main support shafts restricting smooth retraction of hose.

Wrong guide arm position

If guide arm is in side wind position for ceiling mounted reels, hose / cord is bending at a 90° angle over roller bracket assembly causing excessive loss of spring tension. Adjust guide arm to coincide with how hose / cord reel is actually mounted. U-bolt clamps may need to be adjusted accordingly.

Broken main spring, broken spring arbor, corrosion on shaft and hub

Replace broken part with new. For corrosion: disassemble reel and remove corrosion, lubricate and reassemble.

material is leaking from the swivel. What do i do?O-ring worn out or wrong O-ring for material being handled

Replace O-rings with O-ring kit or replace with correct rings for material being handled.

Swivel maybe loose or not enough pipe thread sealant on shaft threads

Replace O-rings with O-ring kit or replace with correct rings for material being handled.

What to do if the reel does not latch?This could mean it has a broken latch spring, bent latch pawl or latch plate. The broken part(s) will need to be replaced.



https://www.autotoolworld.com/assets/icons/video.jpg

Videos

How to replace the latch springClick to View
How to change a guide armClick to View
How to install a spring driven reelClick to View
How to adjust spring tensionClick to View
What to do if the reel does not latch?Click to View



https://www.autotoolworld.com/assets/icons/pdf.jpg

Documents and Downloads

Hose replacement and required wrapsClick to View
Pressure drop / flow rate charts and graphsClick to View
Material compatibility tablesClick to View



https://www.autotoolworld.com/assets/icons/applications.jpg

Parts/Accessories

1HR10043 - Adjustable Bumper StopClick to View
S600608 - 340° Pivot BaseClick to View
600626 - Wall Mounted Universal Swing BracketClick to View

Related Items

Recently Viewed Items